Fault Code 027-452 occurs when another device has been detected on the network using the same IP Address as the Xerox Device

Configurare noua (How To)

Situatie

By default, the printer automatically acquires a network address from a DHCP server. To assign a static IP address, perform the following steps.

To set up a static IPv4 network address:

  1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
  2. Select the [Tools] tab on the Touch Screen.
  3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
  4. Select [IPv4 – IP Address Resolution], and then select [Change Settings].
  5. Select [Static], and then select the [Save] button.
  6. Select [IPv4 – IP Address], and then select [Change Settings].
  7. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
  8. Select [IPv4 – Subnet Mask], and then select [Change Settings].
  9. Enter a valid subnet mask using the keypad on the Touch Screen, and then select the [Save] button.
  10. Select [IPv4 – Gateway Mask], and then select [Change Settings].
  11. Enter a valid gateway address using the numeric keypad on the Touch Screen, and then select the [Save] button.
  12. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.

To set up a static IPv6 network address:

  1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
  2. Select the [Tools] tab on the Touch Screen.
  3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
  4. Select [Enabled], and then select the [Save] button.
  5. Select [Manually Configured IPv6 Address], and then select [Change Settings].
  6. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
  7. Select [Manually Configured IPv6 Address Prefix], and then select [Change Settings].
  8. Enter the prefix using the keypad on the Touch Screen, and then select the [Save] button.
  9. Select [Manually Configured IPv6 Address Gateway], and then select [Change Settings].
  10. Enter the gateway address using the keypad on the Touch Screen, and then select the [Save] button.
  11. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.

Solutie

Pasi de urmat

Fault Code 027-452 occurs when another device has been detected on the network using the same IP Address as the Xerox Device.

  1. Log into the machine as a System Administrator.
    1. Press the Log In/Out button on the Control Panel.
    2. Enter the System Administrator username and press Enter.
    3. Enter the System Administrator password and press Enter.NOTE: The default user is admin and the default password is 1111.
  2. Press the Machine Status button on the Control Panel.
  3. Select the Tools tab on the Touch Screen.
  4. Select System Settings
  5. Select Connectivity and Network Setup.
  6. Select Protocols Settings.
  7. Select IPv4 Address Resolution, and then select the Change Settings button.
  8. Select DHCP.
  9. Select Save.
  10. Press Log out. A prompt to reboot the machine will be displayed. Reboot the machine.NOTE: If the prompt to reboot the machine is not displayed, manually power the machine off and on.

Tip solutie

Permanent

Voteaza

(4 din 14 persoane apreciaza acest articol)

Despre Autor

Leave A Comment?