Soluții

Rezolvarea erorii pr_connect_reset_error din Mozzila Firefox

• Data 03/02/2021
• Autor Octavian Dragoi
• 3
• 681

In cazul accesarii unui site web apare eroarea pr_connect_reset_error in Browserul Mozzila Firefox. In general, aceasta eroare apare din cauza unor erori legate de cache/cookies sau a unor restrictii in firewall/ antivirus.

6 tendințe noi în tehnologie pentru 2021

• Data 03/02/2021
• Autor Stefan Nagy
• -20
• 693

Tehnologia se schimbă de la an la an și aduce cu sine noi tipuri de comportament. Avantajele oferite de tehnologie în lumea afacerilor determină companiile să-și modifice fluxurile de lucru și să adopte cele mai noi soluții tehnice. Dacă nu o vor face la timp, vor deveni necompetitive și se vor confrunta rapid cu o scădere a veniturilor. Pentru anul 2021, Cisco a anticipat 6 tendințe ce vor avea un impact semnificativ în lumea tehnologiei.

Fault Code 027-452 occurs when another device has been detected on the network using the same IP Address as the Xerox Device

• Data 03/02/2021
• Autor Stefan Nagy
• -6
• 2624

By default, the printer automatically acquires a network address from a DHCP server. To assign a static IP address, perform the following steps.

To set up a static IPv4 network address:

1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
2. Select the [Tools] tab on the Touch Screen.
3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
4. Select [IPv4 – IP Address Resolution], and then select [Change Settings].
5. Select [Static], and then select the [Save] button.
6. Select [IPv4 – IP Address], and then select [Change Settings].
7. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
8. Select [IPv4 – Subnet Mask], and then select [Change Settings].
9. Enter a valid subnet mask using the keypad on the Touch Screen, and then select the [Save] button.
10. Select [IPv4 – Gateway Mask], and then select [Change Settings].
11. Enter a valid gateway address using the numeric keypad on the Touch Screen, and then select the [Save] button.
12. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.
13. 

To set up a static IPv6 network address:

1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
2. Select the [Tools] tab on the Touch Screen.
3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
4. Select [Enabled], and then select the [Save] button.
5. Select [Manually Configured IPv6 Address], and then select [Change Settings].
6. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
7. Select [Manually Configured IPv6 Address Prefix], and then select [Change Settings].
8. Enter the prefix using the keypad on the Touch Screen, and then select the [Save] button.
9. Select [Manually Configured IPv6 Address Gateway], and then select [Change Settings].
10. Enter the gateway address using the keypad on the Touch Screen, and then select the [Save] button.
11. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.

How to Enable Cortana to access your device location

• Data 03/02/2021
• Autor digulescu gabriel ionut
• 0
• 515