Soluții

6 tendințe noi în tehnologie pentru 2021

• Data 03/02/2021
• Autor Stefan Nagy
• -20
• 693

Tehnologia se schimbă de la an la an și aduce cu sine noi tipuri de comportament. Avantajele oferite de tehnologie în lumea afacerilor determină companiile să-și modifice fluxurile de lucru și să adopte cele mai noi soluții tehnice. Dacă nu o vor face la timp, vor deveni necompetitive și se vor confrunta rapid cu o scădere a veniturilor. Pentru anul 2021, Cisco a anticipat 6 tendințe ce vor avea un impact semnificativ în lumea tehnologiei.

Fault Code 027-452 occurs when another device has been detected on the network using the same IP Address as the Xerox Device

• Data 03/02/2021
• Autor Stefan Nagy
• -8
• 2611

By default, the printer automatically acquires a network address from a DHCP server. To assign a static IP address, perform the following steps.

To set up a static IPv4 network address:

1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
2. Select the [Tools] tab on the Touch Screen.
3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
4. Select [IPv4 – IP Address Resolution], and then select [Change Settings].
5. Select [Static], and then select the [Save] button.
6. Select [IPv4 – IP Address], and then select [Change Settings].
7. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
8. Select [IPv4 – Subnet Mask], and then select [Change Settings].
9. Enter a valid subnet mask using the keypad on the Touch Screen, and then select the [Save] button.
10. Select [IPv4 – Gateway Mask], and then select [Change Settings].
11. Enter a valid gateway address using the numeric keypad on the Touch Screen, and then select the [Save] button.
12. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.
13. 

To set up a static IPv6 network address:

1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Touch Screen.
2. Select the [Tools] tab on the Touch Screen.
3. Select [Connectivity and Network Setup], and then select [Protocol Settings].NOTE: If the Connectivity and Network Setup option is not displayed, it is required to login as a System Administrator to complete this solution. See the Related Content for additional information.
4. Select [Enabled], and then select the [Save] button.
5. Select [Manually Configured IPv6 Address], and then select [Change Settings].
6. Enter a valid IP address using the keypad on the Touch Screen, and then select the [Save] button.
7. Select [Manually Configured IPv6 Address Prefix], and then select [Change Settings].
8. Enter the prefix using the keypad on the Touch Screen, and then select the [Save] button.
9. Select [Manually Configured IPv6 Address Gateway], and then select [Change Settings].
10. Enter the gateway address using the keypad on the Touch Screen, and then select the [Save] button.
11. If necessary, press the [Log In / Out] button on the Control Panel and then select [Logout] on the Touch Screen to exit the System Administrator mode.

How to Enable Cortana to access your device location

• Data 03/02/2021
• Autor digulescu gabriel ionut
• 0
• 513

Cum sa gasesti modelul si seria unui SSD instalat pe laptop folosind Command Prompt

• Data 03/02/2021
• Autor Marian Chitu
• -4
• 563

Pentru anumite modele de laptop trebuie sa desfaci carcasa pentru a afla modelul si seria SSD instalat pe laptop. Pentru utilizatorul obisnuit acest lucru poate parea dificil de efectuat. Mai simplu este folosirea unei comenzi in Command Promt (Linia de comanda) sau PowerShell.