Stații de lucru

OS - Windows 9182 Solutii

Reguli si plangeri 11 Solutii

OS - OS X 410 Solutii

Reguli de configurare 12 Solutii

Licentiere 18 Solutii

Securitate 182 Solutii

Copie de rezerva (Backup) 68 Solutii

Antivirus 72 Solutii

Aplicatii specifice 5306 Solutii

Hardware 291 Solutii

ESP32 Motion sensor

The ESP32 is a powerful, low-cost microcontroller with built-in Wi-Fi and Bluetooth, making it an excellent platform for motion-sensing projects such as smart lighting, security systems, occupancy tracking, and IoT automation.

1. Motion Sensors Compatible with ESP32

1.1 PIR Motion Sensor (HC-SR501)

Best for: Human motion detection, low power consumption, simple digital output

  • Detects changes in infrared radiation from warm objects
  • Outputs HIGH when motion is detected
  • Detection range: 3–7 meters (typical)

Limitations: Cannot detect stationary objects and has slower response than radar sensors.

1.2 Microwave Radar Sensor (RCWL-0516)

Uses Doppler radar instead of infrared. It is more sensitive than PIR sensors and can detect motion through thin walls, but may cause more false triggers.

1.3 Accelerometer / IMU (MPU6050)

  • Detects motion, tilt, and vibration
  • Common in robotics and wearables
  • Uses I2C communication

2. PIR Motion Sensor Basics

2.1 PIR Sensor Pinout (HC-SR501)

Pin Name Description
1 VCC 5V (some support 3.3V)
2 OUT Digital output (HIGH on motion)
3 GND Ground

Note: Most HC-SR501 modules output 3.3V logic, which is safe for ESP32 GPIO pins.

2.2 Onboard Adjustments

  • Sensitivity potentiometer (detection range)
  • Time delay potentiometer (output HIGH duration)
  • Trigger mode jumper: H = repeat, L = single trigger

3. ESP32 GPIO and Power Considerations

Recommended GPIO pins: 13, 14, 25, 26, 27, 32, 33

Avoid boot-sensitive pins: 0, 2, 12, 15 unless you understand ESP32 boot modes.

ESP32 uses 3.3V logic. PIR sensors may require 5V power. Always connect grounds together.

4. Wiring the PIR Sensor to ESP32

  • VCC → VIN (5V) or 3.3V (if supported)
  • GND → GND
  • OUT → GPIO 27

5. Basic Arduino Code Example

#define PIR_PIN 27

void setup() {
  Serial.begin(115200);
  pinMode(PIR_PIN, INPUT);
}

void loop() {
  if (digitalRead(PIR_PIN)) {
    Serial.println("Motion detected!");
    delay(500);
  }
}

6. Interrupt-Based Motion Detection

#define PIR_PIN 27
volatile bool motionDetected = false;

void IRAM_ATTR motionISR() {
  motionDetected = true;
}

void setup() {
  Serial.begin(115200);
  pinMode(PIR_PIN, INPUT);
  attachInterrupt(digitalPinToInterrupt(PIR_PIN), motionISR, RISING);
}

void loop() {
  if (motionDetected) {
    Serial.println("Motion detected via interrupt!");
    motionDetected = false;
  }
}

7. Power Saving with Deep Sleep

esp_sleep_enable_ext0_wakeup(GPIO_NUM_27, 1);
esp_deep_sleep_start();

This allows the ESP32 to sleep until motion is detected, ideal for battery-powered systems.

8. Common Problems and Solutions

  • False triggers: Reduce sensitivity and avoid heat sources
  • No detection: Allow sensor warm-up time (30–60 seconds)
  • Random resets: Ensure stable power supply

9. Applications

  • Smart lighting systems
  • Home security and alarms
  • Occupancy detection
  • Energy-saving automation.

[mai mult...]